Sistem Telemetri Akusisi Data Injeksi Plastik Menggunakan Xbee Pro S2C
Abstract
Plastic injection machine is a plastic product making machine with an injection molding process. Plastic injection machines at PT Shimano Batam currently cannot be monitored automatically. Therefore, a system is needed that monitors and stores all data about the performance of the plastic injection machine automatically. In this system Arduino Uno is used as a microcontroller of the plastic injection machine signal and the Xbee Pro S2C module is used as a sender and receiver of data packets from the plastic injection machine, the data is processed and then displayed on a PC and stored on the server. The test results of this system show that the machine status data matches the data displayed on the PC. From the results of testing the engine cycle time as much as 11 times, there is the largest difference in processing time, which is 1.20 seconds. From the results of reliability testing, packet loss was obtained by 0.006%. Xbee Pro S2C communication testing with a distance of 1 meter to 60 meters was successful without any data packets lost, when testing Xbee Pro S2C communication with a distance of 85 meters to 110 meters there were 30 data packets lost.
References
[2] A. Hidayatno, A. R. Destyanto, and C. A. Hulu, “Industry 4.0 technology implementation impact to industrial sustainable energy in Indonesia: A model conceptualization,” in Energy Procedia, Elsevier Ltd, 2019, pp. 227–233. doi: 10.1016/j.egypro.2018.11.133.
[3] S. Suhanto, “Rancang Bangun Simulasi Supervisory Control And Data Acquisition (SCADA) Main Distribution Panel (MDP) Berbasis Programmable Logic Controller (PLC),” Jurnal Penelitian, vol. 2, no. 1, 2017, doi: 10.46491/jp.v2e1.111.47-57.
[4] Hafid A., “Perancangan Modul Data Akusisi Pengaturan Kecepatan Motor DC Dengan Masukan DAC Menggunakan Matlab,” Vertex Elektro, vol. 12, pp. 1–58, Feb. 2020.
[5] W. Indani, A. Wahyudi, W. Styorini, and Y. Triyani, “Rancang Bangun Sistem Monitoring Prototype Mesin Packaging Berbasis PLC,” Journal of Applied Smart Electrical Network and Systems, vol. 3, no. 01, pp. 25–32, Jun. 2022, doi: 10.52158/jasens.v3i01.304.
[6] Haryanto H, Permata E, and N. R.U. Nainggolan N. R.U, “Sistem Monitoring Proses Produksi pada Mesin Bardi di PT. Tirta Investama (Danone Aqua) Sukabumi Berbasis Web,” SETRUM, vol. 3, no. 1, pp. 1–34, 2014.
[7] M. Pardede, E. Hutajulu, and B. V. Sundawa, “Sistem Monitoring Tempat parkir Berbasis Arduino Mega Dengan modul Komunikasi XBee Pro S2c,” RELE (Rekayasa Elektrikal dan Energi) : Jurnal Teknik Elektro, vol. 1, no. 2, pp. 48–56, Jan. 2019, doi: 10.30596/rele.v1i2.3012.
[8] T. Ghozali and S. Mulyanti, “Wireless Sensor Network Untuk Pemantau Suhu Ruangan Kelas Program Studi Teknik Elektro – Fakultas Teknik Xbee S2C,” Jurnal Elektro Unika Atma Jaya, vol. 10, no. 2, pp. 117–126, 2017.
[9] T. D. Hendrawati and I. Lesmana, “Rancang Bangun Saklar Lampu Otomatis dan Monitoring Suhu Rumah Menggunakan VB. Net dan Arduino,” Jurnal Teknologi Rekayasa, vol. 1, no. 1, p. 67, Jan. 2017, doi: 10.31544/jtera.v1.i1.2016.67-72.
[10] T. Ghozali and S. Mulyanti, “Wireless Sensor Network Untuk Pemantau Suhu Ruangan Kelas Program Studi Teknik Elektro – Fakultas Teknik Xbee S2C,” Jurnal Elektro Unika Atma Jaya, vol. 10, no. 2, pp. 117–126, 2017.
[11] S. Oktafian Nabilla and E. Ariyanto, “Implementasi Optocoupler Pc817 Dan Relay Sebagai I/O Sistem Remote Reset Axle Counter Az S 350 U Menggunakan Stm32f103c8t6 dengan Ethernet Client Untuk Hubungan Stasiun Weleri-Krengseng,” EPSILON: Journal of Electrical Engineering and Information Technology, vol. 20, no. 1, 2022, doi: 10.55893/epsilon.v20i1.82.
[12] M. Z. M Zulfitra and P. Gunoto, “PERANCANGAN SISTEM KENDALI GERAK ROBOT BERODA MENGGUNAKAN XBEE PRO REMOTE,” SIGMA TEKNIKA, vol. 1, no. 2, p. 133, Nov. 2018, doi: 10.33373/sigma.v1i2.1498.
[13] H. Permana, Topan, and S. Anwar, “Produksi Proses Komponen Plastik Flip Flop Dengan Mesin Injeksi Molding Type Hidrolik,” Jurnal Baut dan Manufaktur, vol. 03, no. 02, 2021.
[14] F. Bu, “An Exploration Of Calculating The Packet Loss Rate By Using The Block Rate,” 2018. doi: 10.2991/cimns-18.2018.33.
Manuscript submission
Submission of a manuscript to the Journal of Applied Electrical Engineering (JAEE) implies that the work described has not been published before (except in the form of an abstract or as part of a published lecture, review or thesis); that it is not under consideration for publication elsewhere; that its publication has been approved by all co-authors, if any, as well as tacitly or explicitly by responsible authorities at the institution where the work was carried out.
The author warrants that his/her contribution is original and that he/she has full power to make this grant. The author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. The author affirms that the article contains no unfounded or unlawful statements and does not violate the rights of others. If copyrighted works are included, the author bears responsibility to obtain written permission from the copyright owners and to appropriately credit the sources.
The use of general descriptive names, trade names, trademarks, etc. in the publication, even if not specifically identified, does not imply that these names are not protected by the relavant laws and regulation.
Copyright Transfer Agreement
The Copyright Transfer Agreement must be signed and return to the publisher of JAEE before manuscript can be accepted for publication. The Transfer of copyright to JAEE becomes effective if and when the article is accepted for publication. if the submitted manuscript is not accepted by Journal, all rights will returned to the authors of the work.
All articles published in JAEE are protect by copyright, which cover the exclusive and unlimited rights to reproduce and distribute the article in any form of reproduction (printing, electronic media or any other form), as well as the translation rights for all languages and countries, for the full term (including extensions and renewals). No material published in the JAEE may be reproduced photographically or store on microfilm, in electronic databases, video disk, etc., without first obtaining written permission from the publisher.
Author's rights
The author may send or transmit individual copies of the final published version of his/her manuscripts any format, including the PDF, to colleagues upon their specific request provided no fee is charged, and further-provided that there is no systematic distribution of the manuscript, e.g. posting on a listserve, website or automatic delivery. However posting the article on a secure network, not accessible to the public, is permitted.
For other purposes, e.g. publication on his/her own website, the author must use the original author-created version of his/her article, i.e. the original submitted file prior to review. He/she may not use the publisher's PDF version. Furthermore, the author may only post his/her version provided acknowledgement is given to the original source of publication and a link (DOI) is inserted to the published article on the JAEE website. The link must be accompanied by the following text: 'The original publication is available at <insert website link here>'.
The author(s) retain all proprietary rights, other than copyright, such as patent and trademark rights to any process or procedure described in the article. The author(s) have the right to photocopy the article for their own personal use.
An author has the right to use (part of) his/her article in subsequent publication of the authors own works provided that written permission is obtained from the publisher and that proper acknowledgement is made to the original source of publication and the publisher. Any other use or reproduction in a collective work requires a fee and permission from the publisher.
The right to grant or refuse permission to third parties to republish part of the article or translations thereof. However, the publisher except at the direction of the contributor(s) will not refuse such permission.
Warrant
While the information in the JAEE is believed to be true and accurate at the date of its publication, neither the authors, the editors, nor the publisher can accept any legal responsibility for any errors or omissions that may be made. The publisher makes no warranty, express or implied, with respect to material contained herein.
